ASTM D3700 - 21
Standard Practice for Obtaining LPG Samples Using a Floating Piston Cylinder
¿Abrumado/a por la IA?
Pasa de la teoría a la práctica con el Taller de IA: Fundamentos Prácticos y Maestría. Próximo 4 de Junio
¡RESERVA TU PLAZA AQUÍ!| Aviso: | Las normas ASTM en lectura se visualizan a través del área de cliente. Los archivos no se pueden descargar |
|---|---|
| Fecha edición: |
2021-12-01
Anulada
|
| Fecha cancelación: | 2021-12-01 |
| Idiomas disponibles: | Inglés |
| Resumen: | |
| Keywords: | floating piston cylinder; hydrocarbon fluid sampling; LP-gas; sampling; |
| Scope: | 1.1 This practice covers the equipment and procedures for obtaining a representative sample of liquefied petroleum gas (LPG), such as specified in ASTM Specification D1835, GPA 2140, and comparable international standards. It may also be used for other natural gas liquid (NGL) products that are normally single phase (for example, NGL mix, field butane, and so forth), defined in other industry specifications or contractual agreements, and for volatile (higher vapor pressure) crude oils. Note 1: Some floating piston cylinders have such tight piston seals that the vapor pressure of some high vapor pressure crude oils may not be sufficient to allow sampling without a handle to move the piston. An alternative sampling practice for UN Class 3 liquids (under 300 kPa at 52 °C) is Practice D8009, which utilizes a Manual Piston Cylinder (MPC) sampler. 1.2 This practice is not intended for non-specification products that contain significant quantities of undissolved gases (N2, CO2), free water or other separated phases, such as raw or unprocessed gas/liquids mixtures and related materials. The same equipment can be used for these purposes, but additional precautions are generally needed to obtain representative samples of multi-phase products (see Appendix X1). 1.3 This practice includes recommendations for the location of a sample point in a line or vessel. It is the responsibility of the user to ensure that the sampling point is located so as to obtain a representative sample. 1.4 The values stated in SI units are to be regarded as standard. 1.4.1 Exception—The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| ICS: | 75.120 - Fluidos hidráulicos |
| CTN: | D02.H0 - D02.H0 |
|
Otras Relaciones |
Es referenciada por D5441 - 21(2025) Es referenciada por D1838-21 Es referenciada por D7995-19 Es referenciada por D6377-20 Es referenciada por D7756-19 Es referenciada por D6667-21 Es referenciada por D2163-23E01 Es referenciada por D2712-23 Es referenciada por D1835-22 Es referenciada por D8009-22 Es referenciada por D4057-22 Es referenciada por D7796-21 Es referenciada por D5274-00R19 Es referenciada por D7453-22 Es referenciada por D8340-22 Es referenciada por D6849-22 Es referenciada por D6730-22 Es referenciada por D1265-23A Es referenciada por D8534-24 Es referenciada por D5799-23 |
Normas citadas
Libros relacionados
Normas relacionadas
Otras colecciones temáticas
