ASTM F606/F606M - 25a
Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
| Aviso: | Las normas ASTM en lectura se visualizan a través del área decliente. Los archivos no se pueden descargar | ||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Fecha de anulación: |
2025-11-13
Anulada
|
||||||||||||||||||||||||||||||||||||||||||||||||||||
| Idiomas disponibles: | Inglés | ||||||||||||||||||||||||||||||||||||||||||||||||||||
| Resumen: | These test methods establishes the standard procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers and direct tension indicators, and rivets. For externally threaded fasteners, the mechanical tests describe the procedures for determining the following properties: product hardness; proof load by length measurement (Method 1), yield strength (Method 2), yield strength of austenitic stainless steel and nonferrous materials (Method 2A), and uniform hardness (Method 3); axial tension of full size products such as fasteners and studs; wedge tension of full size products such as fasteners and studs; tension of machined test specimens including yield point (by drop of the beam or halt of the pointer, autographic diagram, and total extension under load methods), yield strength (by offset, and extension under load methods), tensile strength, elongation, and reduction of area; and total extension at fracture. As for internally threaded fasteners including nonheat- and heat-treated nuts, tests are provided for the determination of product hardness, proof load, and cone proof load. Test for determining the surface and core hardnesses are, conversely, described for direct tension indicators, and through-hardened, carburized, stainless steel, and nonferrous washers. And finally, product hardness testing is described for rivets. The test method for determining embrittlement of metallic coated externally threaded fasteners is detailed as well. |
||||||||||||||||||||||||||||||||||||||||||||||||||||
| Keywords: | compression load; hardness; proof load; properties; tensile; testing; yield; | ||||||||||||||||||||||||||||||||||||||||||||||||||||
| Scope: | 1.1 These test methods cover establishment of procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers, direct tension indicators, and rivets. 1.2 Property requirements and the applicable tests for their determination are specified in individual product standards. In those instances where the testing requirements are unique or at variance with these standard procedures, the product standard shall specify the controlling testing requirements. In the absence of any specified test requirement(s), these test methods shall apply. 1.3 These test methods describe mechanical tests for determining the following properties:
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. Note 1: The values are stated in inch-pound for inch fasteners and SI metric units for metric fasteners. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||||||||||||||
| ICS: | 21.060.01 - Elementos de fijación en general | ||||||||||||||||||||||||||||||||||||||||||||||||||||
| CTN: | F16.01 - F16.01 | ||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Otras Relaciones |
Es referenciada por F467M - 06a(2025) Es referenciada por A563/A563M - 26 Es referenciada por F468M - 06(2025) Es referenciada por A354 - 26 Es referenciada por A193/A193M - 26 Es referenciada por F467 - 24(2026) Es referenciada por A320/A320M - 26 Es referenciada por B1031 - 26 Es referenciada por F468 - 23(2026) Es referenciada por A194/A194M - 26 Es referenciada por F959/F959M - 26 Es referenciada por F3125/F3125M - 25a Es referenciada por F432 - 19(2026) Es referenciada por A962/A962M - 26 Es referenciada por F912 - 26 Es referenciada por F2281 - 04(2024) Es referenciada por A489 - 25 Es referenciada por F436/F436M - 24 Es referenciada por F2882/F2882M - 17(2025) Es referenciada por F901 - 20 |










